How To Remove Battery From Samsung Galaxy Note 5

Introduction

Follow this guide to remove and replace the bombardment in your Samsung Milky way Note5.

Before disassembling your telephone, discharge the battery beneath 25%. A charged lithium-ion battery can catch burn and/or explode if accidentally punctured.

If your bombardment is swollen, take appropriate precautions. Practise not rut your telephone. If needed, you tin can utilise a dropper or syringe to inject isopropyl alcohol (xc+%) effectually the edges of the back comprehend to weaken the adhesive. Swollen batteries tin can be very dangerous, and so clothing eye protection and practise due caution, or take it to a professional if you're non sure how to proceed.

Later completing this guide, calibrate your newly-installed battery.

Insert a SIM eject tool, SIM eject bit, or a straightened paperclip into the small hole in the SIM card tray at the top of the phone.

Insert a SIM squirt tool, SIM eject chip, or a straightened paperclip into the modest hole in the SIM card tray at the top of the phone.
Printing to squirt the tray. This may require some strength.
Remove the SIM card tray.

Using your fingernail, push the S-Pen button until it clicks and pops out of the phone.

Using your fingernail, push the S-Pen push button until it clicks and pops out of the phone.
Remove the S-Pen.

If the glass back is cracked, advisedly record over the entire surface with packing record.
Apply a heated iOpener to the bottom of the phone for about two minutes.
You lot may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, oestrus gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

Apply a suction cup as shut as possible to the bottom border of the phone.
If the phone's back cover is cracked, the suction cup may non stick. Try lifting information technology with strong tape, or superglue the suction loving cup in place and allow it to cure so y'all can keep.
Lift on the suction cup and insert an opening pick under the rear glass.
The rear glass very fragile and can break if yous utilise besides much force or attempt to pry with metal tools.

One time the selection is in place, reheat the edge with an iOpener for some other minute.

Slide the option down the bottom border of the phone.
Go slowly so that the tip doesn't slip out of the seam. If sliding becomes difficult, reheat and reapply the iOpener.
Leave the pick in place to prevent the adhesive from resealing, and grab another pick as you proceed to the next step.

Insert another pick and slowly cut effectually the corner of the phone.
Due to the curved shape of the back, the glass is extremely fragile and prone to cracking in the corners. Be patient and reapply an iOpener if the corner feels hard to piece through.

Earlier cutting further, apply a heated iOpener to the long edge.

Echo the previous heating and cutting procedure for the remaining three sides of the phone.
Get out an opening option in each border of the phone as you continue to the next to forbid the adhesive from resealing.

Use an opening pick to cutting whatsoever remaining adhesive around the edges of the drinking glass.
Lift the glass and remove it from the phone.

To reinstall the back cover:
Use tweezers to peel abroad whatsoever remaining agglutinative from both the back cover and the phone's chassis.
Make clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in i management but, not dorsum and forth. This will help prep the surface for the new adhesive.
Be sure to plough on your phone and test your repair earlier installing new adhesive and resealing the telephone.
Replacement adhesive comes in a pre-cut sail to match the exact contours of the back cover. If that'south non available, you can utilize a loftier-bond double-sided tape, such as Tesa 61395. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
After installing the rear cover, employ strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it nether a stack of heavy books.
If desired, you may reinstall the back comprehend without replacing the adhesive. Remove any big chunks of adhesive that might prevent the dorsum cover from sitting down affluent. Later on installation, heat the back cover and apply pressure level to secure it. It won't be waterproof, but the mucilage is usually more than strong plenty to hold.

Remove the twenty 3.3 mm Phillips screws.

Brand sure yous've ejected the SIM tray before performing this footstep.
Concord the midframe past the edges and lift it upwards while pushing downward against the battery with one finger.
There is a small amount of agglutinative in each corner holding the midframe to the display assembly. Utilize constant force until the midframe separates.
Remove the midframe.

Using the flat end of a spudger, elevator the battery connector straight upward from its socket on the motherboard.

Slide an opening choice under the lesser edge of the battery to slowly pry it upwardly from the case.
The battery is held in identify by strong agglutinative. To assistance with removal, you tin utilise a heated iOpener on the battery for a infinitesimal. Alternatively, apply some isopropyl alcohol under each corner of the battery and let it to penetrate for several minutes to aid weaken the adhesive.
Try your best not to deform the bombardment during this process. Soft-shell lithium-ion batteries can leak unsafe chemicals, catch fire, or even explode if damaged. Do not use excessive strength or pry at the battery with metallic tools.

Slide an opening pick up the side of the bombardment to break apart any remaining agglutinative.

Lift the battery out of the case.
Do not reuse the bombardment afterwards it has been removed, equally doing and then is a potential rubber take chances. Supercede it with a new bombardment.
To install a new battery:
Remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.
Secure the new bombardment with pre-cutting adhesive or double-sided agglutinative record. In order to position information technology correctly, apply the new adhesive into the phone, not directly onto the battery. The adhesive should become around the perimeter of the battery compartment, merely not in the rectangular cutout in the center (which is actually the back side of the display).
Press the battery firmly into identify for v-x seconds.

Conclusion

Compare your new replacement part to the original function. You may need to transfer remaining components or remove adhesive backings from the new function before installing.

To reassemble your device, follow the above steps in reverse order. Take your eastward-waste to an R2 or due east-Stewards certified recycler.

Repair didn't go as planned? Bank check out our Answers customs for troubleshooting help.

Team

Embed this guide

Choose a size and re-create the code below to embed this guide equally a small widget on your site / forum.

Preview