How To Remove Co2 Cartridge From Bb Gun

• GTA »
• All Springer/NP/PCP Air Gun Discussion General »
• American/U.S. Air Gun Gates »
• Crosman-Benjamin Air Gun Gate (Moderators: Gertrude, longhunter) »
• CO2 Cartridge stuck

• Print

Pages: [ane]Go Downwards Share This!

Topic: CO2 Cartridge stuck  (Read 18585 times))

My son wanted to shot today, he doesn't shoot a lot. Anyway he needed a new cartridge and the onetime one is stuck.  His burglarize I just tapped the side and it fell out only the pistol want come out. Is there whatever way to get information technology out without taking the gun apart?

Logged

• Magnolia,TX

CCS 2300, CCS 2400, Custom Built Regulated .25, Custom Built PRod Clone, .308 Bullet shooter, XS46U .177, 850 Hammerli, Custom Built Regulated .177, Benjamin 392, Crosman 2200

---

#one Do not exit cartrdges in the current crop of Crosman CO2 guns. The CO2 wants to adhere to the confront seal and extract it from the valve if yous exit information technology for a long elapsing cranked tight.
#2 Do not tighten the cap any tighter than a half-dozen year old could. IT DOESN't pierce when tightened. It pierces when you fire information technology the first shot. So don't load a pellet on the first shot.
Cranking the cap equally tight as a man CAN volition yield grossly underpowered performance and shortened face seal life.
#3. To get stuck CO2 out take cap off, point at the floor with gun cocked and burn it out.
The seal may come out with the CO2. That's when you get to take the gun autonomously and install a new face seal and kickoff over.
DON'T CRANK THE CAP!
Don't leave it charged
Lube the CO2 tip to go on it from adhering to the face seal
Let the gun come up to temperature Later on Yous PIERCE Information technology SO THE Arrangement Can GET Up TO PRESSURE.
Consistency is a warm gun that is shot so information technology doesn't chill. 45 seconds to a minute between shots lets most CO2 gun recover thermally to be very consistent. The more gas information technology uses each shot the more than chill it sees.
The warmer it is the more power it makes and the more shots it gets. Starting warm is the key. Oestrus is gratis energy. CO2 is very heat sensitive giving 20% more power on a warm twenty-four hours.
Happiness is a warm gun.

TimmyMac1

Logged

"No Guns Would be a Anarchism"

---

Cheers Timmy. I exercise all the things you said in your post except accept it out when not in use. Gauge I'll be doing that from now on.  Looks like I'll be taking this 1 autonomously to remove the cartridge.

Logged

• Magnolia,TX

CCS 2300, CCS 2400, Custom Built Regulated .25, Custom Congenital PRod Clone, .308 Bullet shooter, XS46U .177, 850 Hammerli, Custom Congenital Regulated .177, Benjamin 392, Crosman 2200

---

i had one stuck in a 2260 years ago, tried everything, had to have information technology apart.

Logged

steve

HW95L .22
Diana 52 .22
BSA lightning xl se grt .22
xs28m .22
QB78D .22
Hammerli 850 .22

---

They are Custom Shop guns. The rifle came out after tapping on information technology and dry firing it. The pistol will need taking apart.

Logged

• Magnolia,TX

CCS 2300, CCS 2400, Custom Built Regulated .25, Custom Built PRod Clone, .308 Bullet shooter, XS46U .177, 850 Hammerli, Custom Built Regulated .177, Benjamin 392, Crosman 2200

---

But sat down after supper to start taking the pistol apart and information technology just falls right out. Well it's staying out until the next time.

Logged

• Magnolia,TX

CCS 2300, CCS 2400, Custom Built Regulated .25, Custom Congenital PRod Clone, .308 Bullet shooter, XS46U .177, 850 Hammerli, Custom Built Regulated .177, Benjamin 392, Crosman 2200

---

How long was it in at that place? I leave mine in, just I shoot well-nigh every day... I read that keeping the system under pressure is actually good and then no dirt will enter

Logged

• Farmingham, MA

---

I put mine in the freezer for a couple hours in a cypher lock freezer handbag and the cartridges always come out after..

 Gene

Logged

• http://world wide web.charliedatuna.com  S Carolina

THE ONES I SLEEP WITH:   HW-97K,  Crosman Kantana, CZ-200, Webley/Scott UK Tomahawk, Benji Marauder, Benji Discovery,  Remington NPSS .177, Crosman Venom, Crosman RamQuest, Gamo 440, Gamo S1K, Gamo CFX Synthetic, Gamo CFX Royal,  RWS 24

---

How long was information technology in there? I leave mine in, but I shoot near every day... I read that keeping the system under pressure is actually proficient so no clay will enter

Mayhap 6 months. I idea you was suppose to leave them in to. Just going to have to stop after I empty one so I can take information technology out before I store it away.

Logged

• Magnolia,TX

CCS 2300, CCS 2400, Custom Congenital Regulated .25, Custom Congenital PRod Clone, .308 Bullet shooter, XS46U .177, 850 Hammerli, Custom Built Regulated .177, Benjamin 392, Crosman 2200

---

Existent easy: Loosen end cap for cart a couple turns...point barrel down and cycle commodities/trigger a few times....(then get small hammer) point barrel down and gently tap the loose stop cap a few times..cart should autumn out when you remove terminate cap.
I but at present did mine on an empty cart that was in pistol a year or and so.

« Concluding Edit: Baronial 20, 2022, 03:47:36 PM by crazyhorse1 »

Logged

Discovery.22, Marauder .25, Dominator .22 HPA ,Evantix AR6 DUK .22, 850 Air Magnum CO2 .177, DAR .22,
Avenger .22

---

---

• GTA »
• All Springer/NP/PCP Air Gun Discussion Full general »
• American/U.South. Air Gun Gates »
• Crosman-Benjamin Air Gun Gate (Moderators: Gertrude, longhunter) »
• CO2 Cartridge stuck

How To Remove Co2 Cartridge From Bb Gun,

Source: https://www.gatewaytoairguns.org/GTA/index.php?topic=46131.0

Posted by: duvallfaight.blogspot.com

Share this post