How To Repair Outdoor Lounge Chairs That Ripped

You know how it is, with all that wear and tear in the garden, sometimes patio furniture breaks. You have the pick of paying to get it repaired, throwing it away, or you could fix it yourself! Larn how to wrap a double vinyl strap in this footstep by step guide and repair your furniture on the cheap.

If your pool lounger or patio chaise lounge is missing a strap, you can club a vinyl replacement hither or y'all could even cutting one to size yourself. With over 50 vinyl strap colors to cull from, vinyl strapping replacement is a cost-effective manner to make your outdoor puddle patio and lawn piece of furniture await like new. Sunnilands founder Jeff will evidence you how in this video.

What is a double wrap vinyl strap?

The double wrap is the process of wrapping a vinyl strap over the top of the frame and around it once to hibernate the rivet of the frame. Its a bit catchy to get used to but once y'all get the flow of it youll be fixing all your cleaved outdoor article of furniture with ease.

Tools & materials you will demand: tape measure, vinyl to cut, or pre-cutting replacement straps rivetsfor a double-wrap chaise, a pot with a hat full of boiling water, tongs & oestrus-proof gloves or similar, a cake of wood, a drill, cutters or tin snips.

Time it will take: This is no more than a 10 infinitesimal chore if you get that water humid and prepare to cook those straps right from the start.

Step 1: Remove the one-time strap

Pull off the erstwhile, cleaved strap until you accept the frame with the empty holes underneath. If your lounger frame is a footling dingy, nows your chance to give information technology a quick make clean.

Step 2: Measure strap size

Concord your tape measure around the border of one hole. Wrap your tape twice around the frame until it meets the border of the second pigsty. Image. Then loop the record mensurate around the other side of the lounger and wrap in a similar style. Pull information technology tight and measure the length.

Now deduct ten%. We practise this because the vinyl is stretchy and you want your straps to exist tight around the chair. If we didnt deduct x% and installed it, it would exist sloppy and loose when you sat on it.

In Jeffs case the tape was 33 inches. Minus ten% volition hateful 33-3 =30.

Step iii: Make the straps

Hither we demand a few more items from our list including a piece of wood. This is just something to drill downwards into to make the holes into the straps. We besides need a pair of cutters, or tinstrips, the rivets that we decided we need for our quarter inch hole and the vinyl strapping. We came upwards with a thirty inch measurement so were just going to lay this strap down at the 30 inch marker and cut it straight beyond with the cutters. And equally we demand ii straps, we're going to echo the procedure.

Now take the two straps and cut off the corners so they dont stick out when we get to turn them over. Snip off a small corner on both sides, on both straps.

So well lay them onto the block of wood, keeping them together and keeping our paw away from the end of the drill. Were going to go about a quarter inch abroad from the border of the strap and drill a quarter inch hole into the strap. Just like the flick below.

Do be careful when y'all have that drill near your hands, be certain to push down and away from yourself. Repeat on the other side.

Now were going to have our rivets, these 5/eleven _ inch rivets and button one in each hole. These rivets are super stiff and peachy to use because you dont have to worry about them coming off the article of furniture afterward on.

Tip: I like to put the rivets on the straps on before I rut them, that way Im not fumbling with the straps when theyre hot subsequently.

Now put the straps into a boiling pan of hot water and wait for them to cook for 3-4 minutes. The strap will then become super pliable and easy to work with. If yous tried to practice this without heating the strap you will take a real hard fourth dimension well-nigh it!

Note: If you lot bought pre-cutting straps you will all the same demand to put them in hot h2o.

Step 4: Install the straps

Fish out the straps with a pair of tongs and rut proof gloves if you have them if y'all do it with bare easily it will be too hot to handle.

Plug the strap in below the frame by putting the rivet in the hole and wrap it effectually one time, pulling it snug.

Tip: It always helps to exit a strap on the frame next to information technology to use every bit a guideline. Fifty-fifty if its broken, you can take it off once youve got the hang of it.

Now what I like to practice here is pull it a good 10 inches past the furniture and on top of some other strap as it kind of grips itself a lilliputian. Then Im going to wrap this over the frame and get this over the hole and then permit this go and now I can adjust the strap.

Annotation: The tricky office is trying to concord the strap while you wrap it around the 2d fourth dimension, before you plug in the 2d rivet. But one time you have that you lot can merely give it a tug, and pull it on tiptop where information technology needs to be.

And thats it! Allow the states know how you got on with your projection. If you need any parts, any rivets,pre-cut straps orstrap vinyljust click the links.

Source: https://www.sunnilandpatio.com/blogs/sunniblog/outdoor-furniture-repair-how-to-fix-vinyl-strap-lounger

Posted by: duvallfaight.blogspot.com

Share this post